Stage 1 Boost
The gasoline Stage 1 Boost Cooler kit is available for forced induction applications that are either fuel injected or carbureted. Operation is very simple: the system starts injecting when the boost switch reaches the user-adjustable point and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low to medium boost setups looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, etc.
Kit includes:
- UHO (Ultra High Output) Pump
- 3 Quart Reservoir
- 3 Nozzles To Cover a Wide Range of Horsepower
- Required Hardware Needed For Installation
- Comprehensive Instructions
Stage 2 Boost
This kit uses manifold boost pressure to determine when and how much water methanol to inject. Proportionally injecting according to boost pressure gives the most accurate delivery of water-methanol and allows the most cooling and performance improvement over the widest range. More power and driveability is the result. It can be used on any forced induction engine: carbureted, fuel injected, turbocharged, positive displacement or centrifugal blowers. The most suitable are the centrifugal supercharged and turbocharged engines, as they build boost is a more progressive manner concerning water-methanol injection. The positive displacement blower engines will work, but it might take more work to dial in the delivery.
Kit includes:
- UHO (Ultra High Output) Pump
- 3 Quart Reservoir
- Variable Controller
- 3 Nozzles To Cover a Wide Range of Horsepower
- Required Hardware Needed For Installation
- Comprehensive Instructions
Stage 2 Boost VC-50
The only difference between the "Stage 2 Boost" and this kit is the controller. The VC-50 kit includes Snow's new VC-50 Gauge Controller. The VC-50 offers the functionality of a boost gauge and water-methanol controller all in one! Highlighting a 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) OLED screen displaying boost, percentage of injection, low level, secondary nozzle activation, prime button, and 2 fault codes directly on the screen. Also new, the VC-50 has the ability to progressively command 2 adjustable stages of water-methanol for maximum cooling and HP results.
Stage 2 MAF/MAP
This kit uses the 0 to 5 Volt output signal from the Mass Air Flow sensor on many fuel injected vehicles. This means that any vehicle with a MAF (with a 0-5V output signal) can use this kit, whether they are naturally aspirated or forced induction. If the application is forced induction, it can be used with very fast-spooling turbos, or positive displacement blowers. It is easier to set up with the positive displacement blowers with a MAF signal because it is more progressive in nature vs. the boost pressure signal on those applications. This allows for accurate injection over a wide range. The result is excellent power and driveability.
Kit includes:
- UHO (Ultra High Output) Pump
- 3 Quart Reservoir
- Digital variable MAF controller
- 3 Nozzles To Cover a Wide Range of Horsepower
- Required Hardware Needed For Installation
- Comprehensive Instructions
Stage 3 Boost
The Stage 3 Boost Cooler® is unmatched for accuracy and adjustability in water-methanol injection systems. This system can be used on any forced induction engine, or ANY engine with a traditional EFI system, and features our LCD display with on-the-fly adjustability.
Extremely easy to set up and dial in - the software creates a delivery map based on boost or EFI signal from just a few easy to set points you punch in from the drivers seat.
The LCD Screen displays boost pressure, fuel injector duty cycle, as well as water-methanol injection percent. Quick, easy, positive adjustments are made with 2 push buttons. Low profile design allows for easy-to-view and discrete mounting.
Kit includes:
- UHO (Ultra High Output) Pump
- 3 Quart Reservoir
- 3 Nozzles To Cover a Wide Range of Horsepower
- Required Hardware Needed For Installation
- Comprehensive Instructions
- LCD Screen, Push-button Digital Variable Mapping Controller
- 10 feet High Pressure Tubing (1200psi burst)